All RC fliers have gotten that "I can't tell which way it's going"
feeling when learning to fly RC. Several simple color trimming steps can help
you fly your airplane better, whether you are a beginner or top dog in Pattern.
Most airplanes, especially ARFs, are covered or painted to look good in the
store. But in the air it's a different story. The situation is very simple—if
you can't see it, you can't fly it.
To successfully fly an RC aircraft, the pilot must have good orientation and
distance perception. The eyes estimate aircraft orientation based on the
perceived position of the model's outer edges, and the relationship of these
outer edges to the edges of any discernible trim markings on the airplane's
wings or fuselage. Distance perception, in turn, depends on a combination of
one's perception of the aircraft's outside edges and its estimated orientation.
After you have located your airplane and estimated how far away it is, you must
immediately recognize several attitude orientations:
The following suggestions will help you with distance and attitude
perception. Visual acuity and contrast perception diminish with age, but by
using correct color concepts, even senior fliers will find that visual
orientation of their aircraft can be consistently and reliably achieved.
Solid-Colored Aircraft
RC airplanes are flown in all kinds of weather and background conditions. A
solid-colored aircraft will sooner or later fly into a condition where it blends
into the background. This will result in a complete loss of location and
orientation since no edges can be perceived. The absolute worst, in my opinion,
is a silver Mustang in a heavily overcast sky. Yellow Cubs are tough to see when
back lit by the sun. I had a dark green airplane that would disappear when I
landed with a background of green trees. Red Stiks and dark blue airplanes go
invisible in late evening and storm conditions. A solid-colored airplane is
easier to cover, but it won't do you any favors up in the sky.
Wing and Horizontal Stabilizer Shades
The top of the wing and horizontal stabilizer is normally lit by sunlight. The
bottom of the wing and horizontal stabilizer is shadowed. Coloring the top
lighter and the bottom darker keeps this same relationship even in changing
lighting conditions.
ARFs are classic blunders in coloring. Either they have identical top and bottom wing colors, or they put some token color on the top of the wings and leave them white underneath. They look good in the store, but don't help the beginner at all.
I always recommend that beginners cover the bottom of the wing and the bottom of the horizontal stabilizer with dark-blue contact paper before flight.
When flying at a distance of 500 feet or more (depending on the size of the model and lighting conditions) you can't see colors, because the cones of your eyes that perceive color are 2,000 times less sensitive than the rods, which perceive illumination.
In these circumstances, your gray-scale vision (your perception of lightness and darkness in a black-and-white image) provides your orientation and depth perception, not color. Any series of adjacent colors on your aircraft that are intended to facilitate orientation should therefore be gray-scale opposites. For example, a series of bands consisting of red, yellow, blue, and then white is desirable. Don't assume a series of "color opposites" such as red, green, blue and black will be effective. These all have the same dark gray-scale shade and will show an equal tendency to disappear in a deep blue or heavily overcast sky.
If you use the wrong series of color bands, you won't know how far away your
aircraft is, and you won't even know which way it's heading to bring it pack.
Also, don't rely on intricate patterns. They blend together to form edgeless
fuzz approximately 100 feet away. You can test potential color schemes for
gray-scale perceptibility by video taping and playing back alternative color
schemes on a black-and-white television or on a color television with the color
control turned down.
Actual Patterns to Use (click here to
see the pattern)
The best color scheme for beginners that I have found is a combination of large
starburst patterns on top of the wing and horizontal stabilizer, and a solid
dark color underneath the wing and horizontal stabilizer.
Beginners consistently become perceptually disorientated when flying at a distance, especially when the airplane flies at a 45° angle away or toward the pilot, since the aircraft silhouette is identical. With the starburst pattern, all the beginner has to do is slightly roll the wings towards him, and the starburst pattern becomes an arrowhead, pointing in or out, the direction of flight.
Start by covering the bottom of the wing and horizontal stabilizer with any
dark color. The exact color could be black, deep red, dark blue, or green, it
doesn't matter; they will be the same gray-scale color at a distance. Then put a
2-inch strip of some light color along the leading edge of the bottom. Do the
same for the bottom of the horizontal stabilizer, and make the light strip
roughly 1 inch wide.
The base color of the top of the wing must be a very light color such as white,
yellow, or some other very light color The starburst pattern starts out at the
center of the wing, from 3/8 inch under the wing’s leading edge to roughly 1
inch back from the leading edge at the top. Then it is a large "pie
slice" to the wing tip, where it extends from 3/8 inch under the wing
leading edge to the trailing edge on the top. A second pie slice of a different
dark color extends from the center of the wing to points one third and two
thirds out on the wing. Both sides of the wing are colored like this as is the
top of the horizontal stabilizer.
Landing Considerations
Landing requires keeping your wings flat and knowing where you are in the
landing approach. You are generally close to the airplane during the later
stages of the landing approach, so your color perception is improved, but the
wings will be edge-on to your line of sight. The leading edges should be very
prominent against any background such as blue sky, white clouds, dark overcast,
distant mountains, or green trees. All of these items have spectral lines toward
the higher frequency blue or green region, so a very simple solution would be to
have a low frequency color such as red or orange on your wing and horizontal
stabilizer leading edge.
At the field where I fly in Colorado, ARFs with blue wing edges are almost invisible when a low approach from the West dips the airplane visually below the mountains, resulting in very klutzy landings by beginners.
The leading edge red or orange pie slice is wrapped around the leading edge so that it has the maximum area of visibility when edge on. The 2-inch strip of white on the bottom of the wing near the leading edge will become visible during the landing flare, aiding in precision landings.
I prefer a white background on the top of the wing and horizontal stabilizer,
with a bright red leading edge pie slice and a metallic blue inner pie slice on
trainer airplanes. The same metallic blue under the wing looks nice, but any
dark color works fine
Fuselage and Rudder Coloring
The same coloring rules apply to the fuselage. Keep the top of the fuselage
light, and the bottom dark.
The sides of the fuselage should aid you in flying horizontal passes. A solid color fuselage is very difficult to keep straight and level because all of the aircraft reference lines are curved. Light blue-and-white fuselages (a favorite ARF color scheme) blend in with the sky and clouds too well, and will become invisible under some lighting conditions.
Draw a line along the thrust line of your aircraft, roughly splitting the top and bottom of the sides in half. Make the top half of your fuselage sides a light color. Make the bottom half a dark color, usually one of the wing pie slice colors.
Analyze how you fly. Beginners and experts, who fly inverted much of the time, should make the fuselage line color demarcation exactly follow the thrust line. Beginners fly airplanes with lifting, flat-bottom wings, so the aircraft fuselage side flies a straight line.
The expert flies an airplane with symmetrical wings, so he flies at a slightly raised altitude to maintain level flight, whether upright or inverted. Therefore he should also have the fuselage line color demarcation exactly following the thrust line. When doing a horizontal pass, he should maintain an equal rising thrust line sight picture whether upright or inverted.
The interesting situation is the beginning aerobatic pilot. His routines do
not include horizontal, inverted passes, but his maneuvers do include many
horizontal flight components. He will usually be flying an aircraft with
symmetrical airfoil wings, so the aircraft will be moving through the air with a
slight upward orientation. He should offset the fuselage side color demarcation
upward at the tail of the aircraft by roughly an inch. Now he can practice his
horizontal passes by keeping the fuselage side lines parallel with flat ground.
The vertical stabilizer and rudder should have very wide horizontal bands of
color. Make the top of the horizontal stabilizer the same color as the wing
tips. Then put a light-colored band, and below this a dark-colored band, usually
the same color as the inner pie slice on the top of the wing. The base color of
the vertical stabilizer and rudder should be the same light color of the wing.
Another variant for the vertical stabilizer and rudder that works well on
trainers with very big tails—such as the Kadet series—is a starburst pattern
on the top of the wing. This aids the beginner in determining the direction of
travel when flying at a distance. The tail’s starburst pattern becomes an
arrowhead pointing out the direction of flight.
Looping
Consider what the usual looping problem always is for the beginning aerobatic
pilot. The pilot does not begin the loop with his wings flat. He usually
corkscrews in or out. Proper coloring of his low-wing or mid-wing airplane can
be a major help.
Make the wing tips stand out. I usually make the outer 2 inches of each wing
and 1 inch of each horizontal stabilizer the same bright red that I color the
leading edge. If you follow my advice above on the wing bottom and the fuselage
sides, the wing tip can be visually correctly placed for a perfect loop. If the
wing tip is too high, resulting in a corkscrew out, the pilot will see the dark
wing bottom. If the wing tip is too low, resulting in a corkscrew in, the pilot
will find that the wing tip blends too well with the bottom of fuselage side.
The correct sight picture will be the wingtip cleanly placed against the upper
lightly colored fuselage side. Look at the International Miniature Acrobatic
Club or Pattern airplane pictures in RC magazines. They always have a dark color
on the top half of the fuselage side into which the wing tip blends, causing
looping problems.
Geometric Shapes
Humans can recognize different geometric shapes 1/10 of a second faster than
colors. I use this phenomenon to help me with the vertical rolls performed in
advanced aerobatics. Instead of a solid dark color on the bottom of my wing and
horizontal stabilizer, I put four large circles on the bottom of the wings and
two large circles on the bottom of the horizontal stabilizer. The noticeably
faster recognition of the round shape verses the line shape aids me in nailing
the vertical rolls.
A number of people at my field have copied my bottom circles without knowing
the reason why I use them. The solid colored bottom is preferred unless you are
doing vertical rolls.
Sunglasses
Several years ago I flew with some expensive Serengetti Driver sunglasses. These
had a red tint to them, I guess to cut down on the ultraviolet region. I lost
visual perception on a solid dark blue airplane during a landing approach and
crashed.
Fortunately they were stolen at a hobby store a week later, and I got some RayBan aviator sunglasses with a blue-gray tint. What a difference!
Red is at the low frequency part of the visual spectrum, and blue is at the
high frequency part of the spectrum. Red or yellow-tinted sunglasses reduce all
colors to high-contrast shades of gray, making your aircraft in the air appear
completely different from the appearance of your aircraft at home or in the
pits. Gray, light blue, or light green tinted sunglasses make the airplane in
the air look just like the airplane in the pits, and because your vision is
extended into the high frequency part of the visible spectrum, you will have
twice the visual perception range!
Final Thoughts
Click here to return to the JCRC News page
